Spanning tree problem - HP 1920 24G-POE
Hi all,Hope you can help! We have one HP 1920 connected to a Dell Sonicwall TZ 300 on HP port 1. HP port 2 to connected to a Cisco switch (external network provider). The external network provider has...
View ArticleConfiguration switch comme client DHCP
Bonjour à tous,Je me tourne vers vous car je suis un peu perdu dans la configuration d'une série de switch acquise dernièrement. Nous disposons de 6 switchs HPE 1950 flambant neuf, et je souhaite...
View Articlehpe1920 series do not allow Multipoint services trough trunks.
Hi,i have 3 swicthes, they are in terconnected trough trunks.All traffic runs fine only my multipoint services (windows multipoint 2012 servers) are not running trough the trunking ports. Only the...
View ArticleClik here to view.
Loosing BAGG When assigning New VLAN 5900AF
Hello,I'am facing a very strange issue.I have 2 IRF Stacks based on 2 paris of 5900AF Switchs.Theses stacks are used for theVMware Datacenter connectivity.To connect to my Backbone Switches i have...
View Article1920S Switch, no Auto Voice VLAN after port was TRK member
On two switches 1920S, P/N: JL386A, where after using 2 ports on each switch as TRK and then disabled the TRK and enable again the ports as user ports with the Auto Voice VLAN enabled, the phones don't...
View ArticleProblem with internet time on clients with HP 1820-48G switch
Hey folks.After replacing my Procurve 1810-24G with an OfficeConnect 1820-48G I lost the ability to get the correct time for all of my windows clients.I tried a lot but could not get it to work. The...
View ArticleClik here to view.
HPE OfficeConnect 1920: was R1116 rebuilt and is it now newer than R1117?
Strange, two days ago (August, 29th) I received the usual Routine Alert e-Mail about HPE OfficeConnect 1920 Switch Series saying that "A new software update is now available"...I expected to see a...
View ArticleSwitches with CLI access
HI,Can anyone tell me if any of the switches below have telnet access to the CLI (_cmdline-mode on)?1950 48G 2SFP+ 2XGT PoE+ (370W) - JG963A1920S 48G 4SFP PPoE+ 370W - JL386A1850 48G 4XGT PoE+(370W)...
View ArticleFAN NOISE (HPE 1920-48G - JG927A)
Hello.I know it's probably the case here. But did anyone find a solution how to reduce the noise of the HPE 1920-48G - JG927A switches?Did not anyone try to disconnect the fan? (If applicable, due to...
View Article802.1x on switch 3Com Officeconnect managed gigabit switch not working with...
Hi,i have a problem with switch 3com officeconnect gigabit switch 8 port when i want to use 802.1x feature.i have configured windows server 2012 as a radius server.and then i configured 3com switch...
View Article802.1X on HPE 1950
I'm trying to set up 802.1X on HPE 1950 (JG961A), but it's not working. I tried to set up 802.1X on the HPE 1950 according to pages 122-124 of the user guide...
View ArticleHPE OfficeConnect Switch 1920S 24G Configuration
Hi there,We've recently purchased 1920S as core switch on our remote site. Previously we're using a firewall appliance to configure all vlans and routing but due to the changes of Network Infra, we...
View ArticleHPE OfficeConnect 1920S Configuration Novice
Hello all,OK, so I'm a bit of an educated novice. I'm used to the ComWare version of configuration, but am having difficulty configuring this switch (web interface only, JL381A). I need to have the...
View ArticleCryptic error message HP V1810-48G
Every few months I receive error messages through syslog from one of our three switches (firmware PK 1.34) like this:[-2131330512]: hal_misc.c(96) 1523 %% Jump to NULL! Interrupt: 0x00000000 vector:...
View ArticleHP switches have a problem
Hi, i have a problem with HP 1910 - 48 PoE JG540A switch. The switch is located in our branch, the cameras are connected to this switch, all the cameras are working but the switch does not ping. I...
View ArticleOC20 Management & Features
Hi,we recently received information about the new APs for small environments HPE OfficeConnect 20.The product sheets are looking promising for very small customers with up to 8 APs. But there are a few...
View ArticleTrunking GBIC ports in Procuve 1810G-24
I have several ProCurve 1810G-24 switches I want to link via fiber. with GBIC's inststalled each port (23 or 24) communicates with the other switch. As soon as I make either port part of a trunk is...
View ArticleHP 1920 - 8G-PoE Radius Authentication Web limitations
Hello,I have lots of 1920-8G-PoE switch and I want to login these switches with my Windows 2016 NPS server. I can login many other switches which contain 2626, 2650, 2620, 2610, 5300 series, 5400...
View ArticleCannot log into new switch. Followed directions to a tee. Its not my first...
Just got a J9984a, 1820-48g. Brand new. Setup a laptop with IP 192.168.1.2, 255.255.255.0. Plugged directly into switch.It looks like it connects, but it wont hit the login switch with 192.168.1.1I...
View ArticleHPE OC20 802.11ac (RW) Access Point performance issues
We deployed two customer sites with HPE OC20 devices. Both started to have performance issues with wireless with these new OC20 devices. Transfer speeds especially with SMB transfer from Windows...
View Article