Hey there, i am designing an IPTV network that can stream 4k video from the server. I am going to use HPE Officeconnect 1920s switch as an multicast switch on the network to generate and send IGMP queries to other IGMP snooping enabled switch. My question is can 1920s switch do igmp querier? Thanks.
↧
Can HPE Officeconnect 1920s do igmp querier?
↧
VLNa Routing
Morning all - I work for a company that has a few sites up and down the country. We share network resources with our sister companies from within the same group.
At one of our sites one of our sister company has installed their own router linked into their MPLS cloud. I now need to separate their traffic from ours and point it to their routers.
The site uses the HPE 1920G switches which are web based - I have in mind just to VLAN off their traffic.
There is already a global static route that points to our router, will this prevent their VLAN traffic accessing their routers? Do I need to add anymore static entires?
Many thanks.
↧
↧
HP 1920-24G Vlan configuration
Hi,
I am trying to configure VLAN Concept at HP 1920-24G switch.
I am setting up Windows Based Radius Server(NPS) in my platform, i have 3 switches & a AP between my firewall(testing phase) interlinked to each other.
I configured VLAN option at HP Switch using GUI mode, from firewall to HP Switch-1 i connected a uplink cable at port no 1 which is changed to Trunk Mode, from HP Switch-1 interlinked a cable from Port 2 to HP Switch-2 at Port No 1(both the Port 2 & Port 1) are changed to Trunk Mode, again from HP Switch-2 at Port No 2 connected one more uplink cable to HP Switch-3 at Port No 1(both Port 2 & Port 1) are changed to Trunk Mode.
Finally at HP Switch-3 connected one patch cable at port 23 for my Access point which too changed to Trunk Mode(that didn't worked so changed once to Tagged mode, neither works).
Can anyone please suggest me the right configuration of vlan configuration, as when client tries to connect the WiFi SSID it gets connected but IP not getting assigned based on VLAN ID.
Any help please!!!!
↧
Can not connect to an HP 1950 (JG960A) from a different subnet
I have an HP 1950 switch with no added VLANs or other configuration other than setting the IP and adding a password. The switch is at 10.0.1.106/ subnet 255.255.254.0. From any system on that same subnet, I can ping the switch and also log into the management GUI. We monitor our network with PRTG, it runs on a server on the server network 10.0.10.x, a firewall is segmenting the servers from the client network. The firewall is allowing ping as well as SNMP to the switch & I can see the traffic passing through the firewall. However, the connections fail. I have multiple 1820 switches being monitored some on the 10.0.0.0/23 network and at 18 other locations via an MPLS circuit. We have one other 1950 switch on the server network 10.0.10.x, it monitors correctly. So there is something I'm missing on the problem switch.
↧
HP V1910-16G setting up other VLAN interface cannot PING, only VLAN1 works
Hi,
I got a Hp V1910-16G switch and have updated it firmware to version 5.20_R1519P03.
Am trying to setup VLAN on it as listed below, however after setting the interface IP addresses, the gateway IP of VLAN10, 20 and 1 cannot be PING. Only on VLAN1 it can see the three gateway IPs.
For example I connect a laptop with IP 192.168.200.11 (gw 192.168.200.253). It does not work too when I set IP of laptop to 192.168.150.12 (gateway 192.168.150.253) I was following a vmfocus how tos titled "how to configure layer3 static routes & vlans on hp v1910 24G" I can't seem to find out what's wrong maybe you can help.
I was assuming after setting the interface IP, routing between VLANs will work naturally. But in actual the gateways IP are not ping able for VLAN20 & 10
VLAN1 - 192.168.100.253 for pc users
VLAN10 - 192.168.200.253 for IPCameras/CCTV
VLAN20 - 192.168.150.253 test VLAN
↧
↧
Radius Permissions Issue - 1920-24G-PoE Switch
I've set up a Procurve 1920-24G-PoE switch to authenticate against a Windows NPS server. Authentication is working fine, but authenticated users do not have manager permissions. I've set up a vendor-specific attribute as follows:
Vendor Code: 25506
Vedendor-assigned attribute number: 29
Attribute format: Decimal
Attribute value: 3
Essentially the same NPS policy (aside from this vendor-specific attribute) works perfectly on my Procurve 26XX switches with aaa authentication login privilege-mode set.
Any ideas what's going on?
↧
Radius Permissions Issue - HPE 1920-24G-PoE Switch (JG926A)
I've set up an HPE 1920-24G-PoE switch (JG926A) to authenticate against a Windows NPS server. Authentication is working fine, but authenticated users do not have manager permissions. I've set up a vendor-specific attribute as follows:
Vendor Code: 25506
Vedendor-assigned attribute number: 29
Attribute format: Decimal
Attribute value: 3
Essentially the same NPS policy (aside from this vendor-specific attribute) works perfectly on my Procurve 26XX switches with aaa authentication login privilege-mode set.
Any ideas what's going on?
↧
How to set bandwith in different port
Switche 1920S 48G - JL382A
May i know how to set port to limit bandwith? i can't find "line rate" under QOS section.
↧
HP 1920S Configure GVRP/MVRP
I am trying to find out if the HP 1920S switches are gvrp or mvrp capable.
The switch can do Radius dynamic VLAN assignment and creates the dynamic VLAN even if missing, but it does not have an uplink. This requires disconnected the device and statically creating the VLAN, which would be alleviated if gvrp/mvrp was available.
If a VLAN is created dynamically by Radius you cannot define an uplink (Tagged/Trunked) port for the VLAN as it says it was dynamically created and you cannot define settings for it.
This also means I have to statically create it at the uplink switch as the switch has gvrp on and doesn't know that the switch below is participating in the VLAN because gvrp/mvrp isn't on to let it know.
Essentially, every time I need to configure a VLAN statically on a 1920S, I have to do it statically at the above switch, as well. Adding an unneccessary amount of time for each VLAN.
↧
↧
1820 Setup issue
I have purchased two HP 1820G switches and wants to do simple LAN between two areas. networking is not establishing while connecting between switches. can any one suggest to resolve this issue, since I am new to configuration
↧
HP 1920S VLAN Config
Hello,
on my HP1920S I would like to configure following:
- VLAN 10 - Enterprise WLAN
- VLAN 20 - WIFi Guest
I would like to know how ro do it and if is possible that switxh deines IP adrresses of clients
on VLAN's?
Thanks!
↧
HPE 1920S Access from internet problem
We have changed a ProCurce 2626 to HPE 1920S. The switch is directly connected to the gateway. The switch, the gateway and all server connected to the switch are in the same subnet.
- the server can ping the switch
- the server can ping the gateway
- the server can access the internet
- the server are pingable from internet
- the gateway is pingable from internet
- the switch can access the internet
but the switch is not accessible from internet (no ping, no web access)
only the basic settings are made (IP, Subnet mask, gateway)
↧
HPE Aruba 2930F in a stack - Updating Firmware
↧
↧
HP 445010-001 | 4 / 16Q Fibre Channel Switch | AG308A
Hi
Is it possible to get hold of the firmware for this switch?
Thanks
↧
Port mirroring HPE series 1950
Bonjour,
Je cherche à faire du port mirroring (via interface web) sur un HP series 1950 (modéle JG962A).
Je configure mon port source et destination, j'enregistre avec succès. Le problème étant qu'apréès l'enregistrement, le port source reste le GE1/0/1 et la direction en "incoming".
Le statut du port mirroring est "incomplete".
Résultat, impossible de faire une configuration comme je l'entends.
Quelqu'un aurait-il une idée pour solutionner mon probléme ?
Merci.
Google Translated
Hello, I am looking to port mirroring (via web interface) on a HP series 1950 (model JG962A).
I configure my source and destination port, I register successfully. The problem is that after the recording, the source port remains the GE1 / 0/1 and the direction in "incoming".
The status of the mirroring port is "incomplete".
Result, impossible to make a configuration as I hear.
Would anyone have an idea to solve my problem?
Thank you.
↧
HP 1950 JG961A "xtd-cli-mode"
How can I change this default password?
foes-bent-pile-atom-ship
↧
HP 1920(JG928A) Firmware Bootrom Issue
I'm trying to upgrade the firmware on my HP 1920 switch. I was on release 1114 and noticed that the latest firmware required bootrom 122 or newer. So I checked all the old versions and version 116 was the latest firmware that requires 117 or newer. The switch BootRom was 119, and from previous experience, the Boorom is updated with the firmware automatically. So I upgraded to firmware 1116 but it is still showing 119 for the bootrom.
How can I upgrade to the bootrom 122 so I can upgrade the firmware on the switch to 1121?
↧
↧
HPE 1920S 48G 4SFP ( JL382A) - MAC binding under port security
Hi All ,
Recently , we have bought 6 HPE switches - model HPE 1920S 48G 4SFP ( JL382A) , we are unable to get MAC binding feature under port security like... binding of one printer MAC address on switch port.
Software Version - PD.01.05
OS Version - Linux 3.6.5
Can i enable MAC binding feature by upgrading Software version.
Need urgent help.
Thank you
↧
HPE 1920S Access from internet problem
↧
HPE 1920S 48G 4SFP ( JL382A) - MAC binding under port security
↧