Trunk switch 1820 serie
Hello,How can I perform a trunk between switches ports?Thank youMatteo
View ArticleHPE 1920S how to disable the admin default user
Hi, hope somebody can help me. I've added two new user with read/write-rights and for security reasons, now I want to disable the default admin user. But I can't find any way to do this, neither in the...
View ArticleHow To Disable Radio 2.4 GHZ HPE OC20
Hello , EveryoneI would like to know how to turn off the HPE OC 20 WIFI 2.4 GHZ wave because my phone is connected to 2.4 GHZ.
View ArticleHPE 1820 VLAN help
Good day, I ask you to help me figure out the organization of vlan in the office network. What do we have:The Cisco RV320 Router on which to create the subnets: MGMT 10.100.5.0/24 VLAN 5 - DHCP OFF -...
View ArticleConnecting four 1920 switches
Hello!I'm going to setup four HP 1920 switches, and i just need to connect them with a uplink cable, so they perform as single network.Basically, 40 Client PCs, one Server and one Gateway and they all...
View ArticleConnecting four HPE 1920 switches
Hello!I'm going to setup four HPE 1920 switches, and i just need to connect them with a uplink cable, so they perform as single network.Basically, 40 Client PCs, one Server and one Gateway and they all...
View ArticleMIB for 1820 Series
We have a lot of HPE1820 starting from 8 port to 24 both nonPoE and PoE variants across the network and are trying to set up monitoring of them all using SNMP but I cannot find where to download MIB...
View ArticleIssue with simple VLAN on 1910-8-PoE+ JG537A switch
Hi All,I do not have very much knowledge about Vlans, but I thought, this simple one, with only one switch can't be a big issue… well it could…I want to connect security cameras and Wifi APs to my...
View ArticleIRF TRAFFIC VERY SLOW
HI all I have 6 switches connected to irf & two uplink.Network performance through this stack is very poor.Regards,Salim
View Article3COM 3CDSG8/hp v1900 8g
The switch being used lost the image on a power outage. I have changed the boot area and it appears all areas have lost the image. I can connect via console but cant seem to get the switch to accept...
View ArticleJE009A ABA vs ABB
Hi, what's the difference between the JE009A switch's ABA and ABB 'tag'?I've found a similar question on a non-HP forum for another switch, the best guess there was for supported languages, which...
View ArticleHP1950 broken web interface
I have a stack of 4 HP1950s, two JG962A and two JG963A working together in an IRF stack. All of a sudden the management interface is broken. I can login but after that the menu remains empty only an...
View Articleadvanced ACLs example 1920S
Someone can give an example of an ACL that denies IP traffic between two VLANs VLAN 110 and VLAN 130. I have tried to do it using advanced ACL and it has been impossible.Please help
View Articleproblems with intervlans communication
hi and sorry for my bad english,i have some problems of configuration on my new installation.i have 2 switch (2530 and 1920s) behind a stormshield appliance.on the old installation we haven't vlan yet,...
View ArticleHP 1950 JG961A IP-HELPER
i have a HP 1950 JG961A and i wish to add a DHCP helper to a vlan. i can't find an option in the GUI and i can find even less in "xtd-cli-mode".Infact in xtd, i can display settings but i can't seem...
View Articleoc20 config via console port
Hi, i need to turn off the 2.4ghz radio signal in my oc20, i have connected via the console port, but have no options to turn off the 2.4ghz, does anyone know if this is possible or how to do it?
View ArticleHP 445010-001 | 4 / 16Q Fibre Channel Switch | AG308A
HiIs it possible to get hold of the firmware for this switch?Thanks
View ArticleHP 1950 JG961A - ACL to vLAN
I have a HP 1950 JG961A and I have created an ACL (v4) in the GUI but I can't see how you append this ACL to a vLAN ?? Please advise.
View ArticleOdd STP related problem in V1910 with a stacked switch
I have a very straightforward network to deal with, a central switch made up of two stacked Edgecore ecs4510-28F switches feeding 11 V1910-48G switches.The feeds are dynamic, LACP controlled, LAGs of...
View ArticleHPE OfficeConnect Switch 1920S JL384A ARP Proxy
Hello, I am new to HP (networking too) and trying setup 1920S switch so pardon me if I ask what I supposed to know.We own ancient Siemens PLCs with no option of setting gateway. The network setup...
View Article