[ABUSE] By: mfubar / Board: switching-e-series-forum (9730)
Please move to Web and UnmanagedLink to post:(Access list issue) by mfubarhttp://community.hpe.com/t5/ProCurve-ProVision-Based/Access-list-issue/m-p/6847121#M9730<p>HP 1920 access list...
View ArticleInterface up down
Hi All,One of our HP V1910-16G Gig 1/0/1 interface going down for few sceonds at same time and we are not able to identify a possible cause :%Mar 8 20:21:06:612 2002 V1910-16G IFNET/4/LINK UPDOWN:...
View ArticleAccess list issue
HP 1920 access list issue. I have a case where I have a vlan for guest/public access. The vlan is 4000 172.16.0.0/24. I only want this vlan to get internet access. I also need it to access a dc...
View ArticleIsolate VLAN - 1910 - 500
Hi.I would like to know how I can isolate a specific vlan from the other vlans without using an ACL to deny the traffic?Denying the traffic through an ACL works but I would like to do the inverse....
View ArticleWhat's the diff? Trunk vs just connecting a cable?
I have three HP Procurve 1810g-24 switches and am going to be linking them together. The first I can only connect one physical network cable to the second due to existing in wall wiring between the...
View ArticleHP 1920 24G Switch configuration LACP
Dear Friends,I am configuring 1920 24G switch please help me to these device accessing gui modethanks
View ArticleDisable ports from CLI interface on 24 port 1920G Switch
Hi everyone from Italy !I'm trying to disable the port state of some of my 24 ports 1920G switch, but I don't find the commands that can do it from CLI interface. Obviously I see how to do it from web...
View ArticleHelp with 1820 VLAN configuration
I'm somewhere beneath novice status in networking, and would welcome some pointers. I have an 1820-8g switch serving a trunked NAS, a PC, and a VoIP adaptor. The switch has a port connected to a dumb...
View ArticleHP 1950 Voice VLAN setup
We are adding 2 x 1950 switches onto our network and I'm struggling to setup Voice VLAN on it.We have 2 VLANs: VLAN 100 for DATA and VLAN 400 for VOICE. All users connect their laptops onto the...
View ArticleUpdating HP 1910-24G to newest firmware makes it reboot indefinitely
Hello,We have some spare 3Com switches (Original name : Baseline switch 2928 SFP Plus) that we want to use. After reseting them, I saw that their firmware was rater old (from 2010). So decided to...
View Article1920-24G ARP table question
Hi,I have purchased 5 x 1920-24G switch for a small office, I have ~25 users with mobile device and printers let's say around 50 clients.I don't have special requirements, I basically use the access L2...
View ArticleHP Procurve 1910 not reachable with ping/http
Hi,I took over 7 HP Procurve 1910 Switches, only one is available via ping/http. I have an old documentation with the Management-IPs for them but only one is working. Is there a way to find out the...
View ArticleDHCP disconnects in VLAN
Hi all,I have a HP 1910 configured with 3 vlans. One of them has dhcp-relay enabled.DHCP-Service and DHCP-Snooping are globally enabled. All fine so far.The problem is, if I reboot the DHCP-Server...
View Article1950 JumboFrames
Hi,Got a few HP 1950 switches, mixed with some Cisco and Ubiqutii gear. All works fine with VLANs etc. But I can't get the HPs to do jumbo frames. Under Network->Interfaces I can set the frame...
View ArticleHP 1920 Switch vLan
On all of my other HP switches I can run these commands:switch#config tswitch(config)#vlan 61switch(vlan-61)#voiceswitch(config)#endTag the ports I want and for vLan 61 and my Polycom VoIP phones will...
View ArticleHp 1920 Vlan Setup
Hi,Im installing a Hp 1920 swich, like in the image, and i setup like this:Vlan10- ip:192.168.1.198 Mask:255.255.255.0Vlan20- ip:192.168.20.1 Mask:255.255.255.0vlan30- ip:192.168.30.1...
View ArticleHelp needed with resetting HP1920 48G (JG927A)
Hello - We have an HP 1920 48G that we forgot the password to, so we need to clear the password or do a factory reset as a next best option. Does anyone know how to do either of these on this switch?...
View ArticleHp 1920 24G Stack and Link Aggregation
hi,I´m conecting two 1920 swich, and i configure a Stack, and it works then i try tu set up a Link Aggregation between the two swich but this don't work and the stack stop wotking too.The Stack...
View Article1810-24G stuck in self-test (J9803A)
From what I can see, the 1810-24G switch that I have is stuck in self-test mode, or isn't completing the boot sequence. When I plug it in, all of the LEDs (port and power) light as usual, then all of...
View ArticleHP 1920-24G DHCP Relay Problem
Hi,I´m trying to put the DHCP Relay working on my Hp 1920 swich, my setup is just for test only for now, and i have a cheap Tp-Link router that as the DHCP server enable and its connected the swich...
View Article