Hello,
I'm wondering if the LACP protocol in Procurve 1800's family switches is based only on MAC address or uses also IP informations. I need to configure link aggregation of two Qnap NAS and I'm not sure the level of LACP in use on the switch. I think it'd be , probably, just MAC based being a level2 switch, but I could be wrong either.
Has someone the answer to this point?
Thanks a lot.
Will the Procurve J4858C SFP work in the new OfficeConnect 1820 24G and 48G switches?
Hi everyone, good morning (at least here in Brazil).
So, I recently purchased a HP Switch 1920 (JG925A) and I am trying to do an ACL between all my network and my server. My need is to block all mac address to access my server, and only some computers will get the access to my server. In resume: block all (with mac address acl) and release some (also with mac address acl).
The firmware of the switch was updated to the last version (2017).
I do not find any document with the right procedure and/or the rigt mac address wildcard schema to reach my goal.
Thanks for the help.
Hi,
the switches are really beta or not proved in praxis.
We have defined management interface in a non-standard-routed vlan, and firmware updates will not load without error message. You need a Server in the same subnet as the mangement interface, and its work ...
So it works with our test switch after 2 hours of testing ...
But with our switch in the real net its horrible. This switch has a own internal signed cetificat, and http management is out, only https.
AFTER upgrading from 1.07 to 1.08 the Switch restart, and it works as switch well, incl. sNMP.
But now the web server of the 1920S doesn´t work - port 443 (and 80) are down!!!
Because ohf HPE politic to reduce mangement port and don´t give telnet/ssh, the only connectiopn is dead.
You are so good, HPE .. and now?
Restarting the Switch doesn´t help, and i cannot press factory defaults because it´s a configured active switch.
where are your backdoors?
Your politic to give a complete new beta-switch technique the unique typ-Name "1920" as the proved old serie, is more as naughty
Gymbox Fitness is a full service Gym in Texarkana Texas. You can join our family for as low as 9.99/month. We believe you should break a sweat, not a budget! With 24hr gym access, tanning & Hydromassage, choosing another gym in Texarkana Tx would be crazy! We also a cardio machines and strength training. Be sure to also sign up for one of our many group classes. (Yoga, Zumba, Piyo and Kickboxing) We can't wait to have you as a wonderful part of your community! See you soon!
Good day!
I can not find the snmp OID for the 1920s switch, such as the CPU usage and memory usage. The OIDs for the 1920 model do not work (1.3.6.1.4.1.25506.2.6.1.1.1.1.6.8)
Tell me please.
Does HPE 12904E support:
1) MACsec?
2) Does it support MAsec in all it's ports?
3) Does it support MACsec with AES 128 and 256 encryption?
4) Does it support REST API?
Dear support;
When I connect with the mobile app on the HPE OC20, the case is like the picture, I wait 100% load and then lose connection, the connection is back to the original. Help me
Hello, friends!
In network, switch 1920-8g has very high cpu usage. Over 70-80% used by process INFO. There are 2 end users connected and 2 trunk in switch. I replaced switch with another one 1920-8g PoE+ (65w), (configuration the same). Everything remains as it was.
Why INFO used so many cpu time?
<KB-HP1920-ochistnye>display cpu-usage history
100%|
95%|
90%| #
85%| #
80%| ##
75%| ## # #
70%| ############ ############ ########
65%| ############ ############ ########
60%| ############ ############ ########
55%| ############ ############# #########
50%| ############# ############# #########
45%| ############# ############# #########
40%| ############# ############# #########
35%| ############# ############# #########
30%| ############# ############# #########
25%| ############# ############# #########
20%|############## ############# #########
15%|############################################################
10%|############################################################
5%|############################################################
------------------------------------------------------------
10 20 30 40 50 60 (minutes)
[KB-HP1920-ochistnye-hidecmd]dis cpu task
===== Current CPU usage info =====
CPU Usage Stat. Cycle: 17 (Second)
CPU Usage : 100%
CPU Usage Stat. Time : 2018-06-10 14:32:20
CPU Usage Stat. Tick : 0x5e3(CPU Tick High) 0xcf8b88e0(CPU Tick Low)
Actual Stat. Cycle : 0x0(CPU Tick High) 0x12befd54(CPU Tick Low)
TaskName CPU Runtime(CPU Tick High/CPU Tick Low)
VIDL 0% 0/ 2acdca
TICK 0% 0/ 47480
STMR 0% 0/ 7544
LOS 0% 0/ 6621
WA_M 0% 0/ 1447e
SYSM 0% 0/ 103d
LED 0% 0/ 30bc
LED3 0% 0/ 4cf6
MacV 0% 0/ b95
AtkT 0% 0/ 911
NICR 10% 0/ 1f22aae
Flow 0% 0/ 1e058
LinT 0% 0/ ba61
Rout 0% 0/ 4bf79
vt0 0% 0/ d1ea0
PSED 0% 0/ 28ea0e
IPCB 0% 0/ 1954d
RPCQ 0% 0/ 1759d
IPCM 0% 0/ 22fd
INFO 80% 0/ f2ca397
DEV 0% 0/ 4629
SOCK 0% 0/ 2dbba
ACL 0% 0/ 781b
MacT 0% 0/ 1225
AgeT 0% 0/ 66fc7
LAGG 0% 0/ 1c4f
MSTP 0% 0/ 9e11c
GARP 0% 0/ 6efd
CLST 0% 0/ 59dd
NDP 0% 0/ 1daa
NTDP 0% 0/ 1c87
HABP 0% 0/ 14bd
LLDP 0% 0/ 10a83
ARP 4% 0/ db06a2
IP 0% 0/ 27104
FSLH 0% 0/ 21d4
FSLR 0% 0/ 4cf7
NTPT 0% 0/ 4653
VTYD 0% 0/ 21c0f
DHSE 0% 0/ 9e9e
ND 0% 0/ ae29
AGNT 1% 0/ 30af5f
DT1X 0% 0/ 1063f
ACM 0% 0/ 7de2
LS 0% 0/ 496d
RDSO 0% 0/ 6a13
RDS 0% 0/ 70d
SC 0% 0/ 276b
NAT 0% 0/ 114f
IGSP 0% 0/ 4eac
STND 0% 0/ 2c26
ROUT 0% 0/ 1d76e
IFNT 0% 0/ 1c4c
DrvT 0% 0/ 32f9
Please help me to resolve this issue.
Best regards, Yurii.
Hello Everyone,
I have a small-to-none experience using VLANs, although I understand the overall concept. I went into a problem recently where one of my customers bought a few Access Points that should connect wireless guests to a VLAN, but his envinronment is not yet completely ready to use VLANs.
The company has 5x V1910/1920 switches and a few smaller ones from Planet that are "Vlan Transparent" as Planet says. I have a DHCP server running on VLAN100 (it's a mikrotik) and the Access Points area connecting GUESTS to the same VLAN100.
Apart from this DHCP server running on VLAN100, there's another DHCP server running on a Domain Controller. Those V1910/1920 are "unconfigured" (IE all ports configured as ACCESS and VLAN001).
If I move the Mikrotik and an Access Points to the same Planet Switch they are ok (Wifi guests receive IP just from the DHCP running on the VLAN100), but any other that need to transpass a V1910/V1920 can't connect to the DHCP server. As a temporary solution I considered changing all the ports to Hybrid and add a tagged VLAN100 to all of them. Should it work?
We are remapping the entire Network to set VLANs properly, but it should take a few days and we need to rush a simple solution for those wifi guests.
Thank you,
I can't seem to find out where from to download fw and docs for the HP V1910 series of switches.
Can someone here show me a link to a download site?
I am experiencing a few ssues with our 1920-24G and 1910 switches. First the VLAN tagging is not working on the SFP port. Secondly when I want to save a configuration the system never comes back to say save succesfully this works perfectly on other switches though. This however isn't critical as it seems to save it although it never confirms that it does. I did try different browsers as well.
The VLAN tagging however is an issue and it was tested on the Gigabit port 24 as an uplink and is working perfectly fine. As soon as we use the GBICS module with exact same vlan tagging on it, the end devices don't get an IP assigned. The GBICs modules used are both HP compatible and branded (J4858D and J4858C) Also the link is up between the 2 switches when using the SFP ports and data flow as expected except for tagging of the VLANs. When we switch to the copper on port 24 the Tagging works again. Both switches have been upgraded to latest firmware available. I have changed the link type from trunk to hybrid with no difference at all. Currently it is set as a trunk.
Below is the interface status of the SFP port 25 with Gigabit interface 24 Disabled
GigabitEthernet1/0/25 current state: UP
IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: d894-0353-13f9
Description: GigabitEthernet1/0/25 Interface
Loopback is not set
Media type is optical fiber, Port hardware type is 1000_BASE_SX_SFP
1000Mbps-speed mode, full-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
Flow-control is not enabled
The Maximum Frame Length is 9600
Broadcast MAX-ratio: 100%
Unicast MAX-ratio: 100%
Multicast MAX-ratio: 100%
PVID: 1
Port link-type: trunk
VLAN passing : 1(default vlan), 10, 20, 100
VLAN permitted: 1(default vlan), 10, 20, 100
Trunk port encapsulation: IEEE 802.1q
Port priority: 0
Last clearing of counters: Never
Peak value of input: 1056 bytes/sec, at 2000-04-26 12:34:02
Peak value of output: 2358 bytes/sec, at 2000-04-26 12:34:02
Last 300 seconds input: 15 packets/sec 1056 bytes/sec 0%
Last 300 seconds output: 15 packets/sec 2358 bytes/sec 0%
Input (total): 4544 packets, 311837 bytes
309 unicasts, 4165 broadcasts, 70 multicasts, 0 pauses
Input (normal): 4544 packets, 311837 bytes
309 unicasts, 4165 broadcasts, 70 multicasts, 0 pauses
Input: 0 input errors, 0 runts, - giants, - throttles
0 CRC, - frame, 0 overruns, 0 aborts
- ignored, - parity errors
Output (total): 4596 packets, 696046 bytes
440 unicasts, 4134 broadcasts, 22 multicasts, 0 pauses
Output (normal): 4596 packets, 696046 bytes
440 unicasts, 4134 broadcasts, 22 multicasts, 0 pauses
Output: 0 output errors, - underruns, - buffer failures
0 aborts, 0 deferred, 0 collisions, - late collisions
- lost carrier, - no carrier
Below is the status of Interface Gigabit 24 with SFP 25 disabled
GigabitEthernet1/0/24 current state: UP
IP Packet Frame Type: PKTFMT_ETHNT_2, Hardware Address: d894-0353-13f8
Description: GigabitEthernet1/0/24 Interface
Loopback is not set
Media type is twisted pair, Port hardware type is 1000_BASE_T
1000Mbps-speed mode, full-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
Flow-control is not enabled
The Maximum Frame Length is 9600
Broadcast MAX-ratio: 100%
Unicast MAX-ratio: 100%
Multicast MAX-ratio: 100%
PVID: 1
Mdi type: auto
Port link-type: trunk
VLAN passing : 1(default vlan), 10, 20, 100
VLAN permitted: 1(default vlan), 10, 20, 100
Trunk port encapsulation: IEEE 802.1q
Port priority: 0
Last clearing of counters: Never
Peak value of input: 24948 bytes/sec, at 2000-04-26 12:17:31
Peak value of output: 92209 bytes/sec, at 2000-04-26 12:06:00
Last 300 seconds input: 126 packets/sec 20427 bytes/sec 0%
Last 300 seconds output: 130 packets/sec 31553 bytes/sec 0%
Input (total): 65084 packets, 16473380 bytes
26518 unicasts, 5348 broadcasts, 33218 multicasts, 0 pauses
Input (normal): 65084 packets, 16473380 bytes
26518 unicasts, 5348 broadcasts, 33218 multicasts, 0 pauses
Input: 0 input errors, 0 runts, - giants, - throttles
0 CRC, - frame, 0 overruns, 0 aborts
- ignored, - parity errors
Output (total): 87064 packets, 58310632 bytes
50866 unicasts, 5307 broadcasts, 30891 multicasts, 0 pauses
Output (normal): 87064 packets, 58310632 bytes
50866 unicasts, 5307 broadcasts, 30891 multicasts, 0 pauses
Output: 0 output errors, - underruns, - buffer failures
0 aborts, 0 deferred, 0 collisions, - late collisions
- lost carrier, - no carrier
Hi,
I am trying to configure vlans across two switches, a 3com 4200g and hp 1910 48 port, I configured everything but the problem is with permitting multiple vlans on the 1910 trunk.
On the interface of hp switch I select the trunk port and select pvid vlan 2 for example, but how can I add multiple vlans to be tagged? it seems you can only add one vlan as tagged.
Hello,
I have connected an Alcatel IP Phone on my HP1810 switch.
The phone deosn't receive any ip address from the DHCP server but if i connect the same phone on a hp2510switch, il is working fine.
Could somebody met this problem ?
Bonjour ,
Je voudrais de l’aide en français s’il vous plaît pour des bornes wifi HPE OfficeConnect OC20-RW
Serial : Confidential Info Erased
Serial : Confidential Info Erased
Je suis en train d’installer ses deux nouvelles bornes wifi avec l’application mobile « HPE OfficeConnect WIFI portal app » mais je n’arrive pas à finaliser l’opération. Les bornes sont bien détectées par l’app, et quand je désire « configurer », je crée un nouveau compte, et à la fin l’app me dit « Problème d’activation du réseau ». Et ceci sans fin, Quand je recommence l’opération, c’est toujours le même résultat.
Avez-vous des soucis en ce moment sur le serveur RADIUS pour l’authentification ?
Je vous remercie de l’aide que vous pourriez m’apporter.
PS : J’ai déjà fait cette opération sans soucis pour un autre client (6 autres bornes) et ça a fonctionner sans problème.
Merci à vous.
Giovanni GADALETA
Hi,
I am trying to configure vlans across two switches, a 3com 4200g and HPE 1910 48 port, I configured everything but the problem is with permitting multiple vlans on the 1910 trunk.
On the interface of hp switch I select the trunk port and select pvid vlan 2 for example, but how can I add multiple vlans to be tagged? it seems you can only add one vlan as tagged.
Bonjour,
J'ai un switch HP 1920-24G dont le port N° 1 à un link type à "hybrid" ce qui me permet de connecter mon serveur de téléphonie IP à ce switch sur un VLAN dédié.
Bien que la vitesse de ce port soit à auto et le port du routeur sur lequel est branché ce switch soit aussi à auto, la négociation se fait uniquement à 100M alors qu'elle devrait se faire à 1GB. Si je force la vitesse à 1GB du côté du routeur je perd la connexion au switch.
D'où ma question : Est-ce qu'un port dont le link type est "hybrid" est limité en vitesse ?
Merci,
Olivier
Google translated
Hello,
I have a switch 1920-24G HP whose port No. 1 to a link type to "hybrid" which allows me to connect my IP telephony server to this switch on a dedicated VLAN.
Although the speed of this port is auto and the port of the router to which this switch is connected is also auto, trading is only 100M while it should be at 1GB. If I force the speed to 1GB on the side of the router I lose the connection to the switch. Hence my question: Is a port whose link type is "hybrid" is limited in speed?
Thank you,
Olivier
Dear all,
I would like your suggestions on a network setup as I am fairly new to networking, we are about to upgrade the setup and I am going to take a deep dive into networks.
The new equipment includes HPE 3810 core switches and HPE 1910 48Port PoE+ as access switches. We are also planning to go to IP Phone solution so trunking is necessary for the ports that we be for workstations and ip phones.
The problem here is that users need to have access to Database/SQL servers via RDC so enabling IP routing for vlans communication without ACL (in the beginning) is, in my opinion, the only way to make the transition a bit smoother.
We currently have a 192.168.x.x/24 network and the new network will be something like:
IT: vlan2 - 10.10.2.0/22
Workstations: vlan10 - 10.10.10.0/22
Machines (industrial-engineering company): vlan20 - 10.10.20.0/22
WiFi: vlan30 - 10.10.30.0/22
Voice: vlan40 - 10.10.40.0/22
The configuration that a partner suggested for the HPE 1910 switches is:
Port 1 untagged vlan 2
port 2-48 untagged vlan 1 (Vlan1 configured with loopback address – no access)
port Trk1 untagged vlan 2, tagged 10,20,30,40
port 49-52 Trk1 LACP
Having every unused port disabled isn’t much better than leaving it active with no access?
I also don’t get why vlan2 (IT Mgmt) need to be untagged at port Trk1, having every vlan tagged isn’t best practice? So the port Trk1 can be set with all the vlans tagged?
Layer 2 switches will be used, at least 1 or 2 so I think tagging every vlan is essential, am I right?
I would like to have your opinion on all that and which configuration would you suggest for the vlans and the switches?
Thank you!
Hi, i am new to switch configuration. I have two switches, A and B as show in attached picture, switch A connected with internet modem and provide internet connection to switch B. PC at switch B need to access share folder pc at switch A for their share files.
I planning to subscribe another internet plan (internet B as show in picture) and direct plug in the new internet modem to switch B while switch B still connected to switch A for access to share folder and internet A. Because some user at switch B need to access to share folder and internet A.
May i know how do i assign particular port at switch B to access internet B only, and no access to internet A? Because some user at switch B are hogging internet A bandwidth and make internet speed slow down.
Start your Preparation for SAP C_AUDSEC_731 and become Authorization and Auditing certified with erpprep.com. Here you get online practice tests prepared and approved by SAP certified experts based on their own certification exam experience. Here, you also get the detailed and regularly updated syllabus for SAP C_AUDSEC_731.