HP 1920-24G and DSCP 46
Just wander if somebody could help me to find answer for my problem. I mark IP packets on device connected (laptop’s NIC) to HP 1920-24G with DSCP 46 – so packet which ender switch is marked with...
View ArticleHp 1920-g24 quality of service for voice
I'm trying to prioritize traffic for voip on Hp 1920-g24 using DSCP 46 and WRR queue. Is it enough if I enable trust for DSCP on port or do I need to do anything else? Could you advise please?
View ArticleHP1810G-24 - Trunk transmitted packets with errors
Hi there, I have two static trunks set up with two ports each. These are connected to two ESX hosts, each with two NICs, connected to a standard vSwitch and an IP hash load balancing. In "Status/Port...
View ArticleHP 1920 - extreme slow VLAN routing
i have new HP 1920-24G Switch JG924A, Software Version 5.20.99 Release 1106there are 2 vlans on it - vlan200 (servers) and vlan201 (workstations)i want to route between these vlans and assign vlan ip...
View ArticleHP 1920
Hello,Pleaseknowsomeonetell me what isthe passwordto release theswitch configurationcommands1920JG924A(_cmdline-modeon)?thank you
View ArticleHP 1920: ARP table size?
Hi, does anyone know whether the ARP table is limited on the the HP 1920? (On 1910G the table is limited to 256 entries...) Regards,
View ArticleHP 1910 802.1x authenticates, then drops
I'm used to working with 5400, 2910 switches and the CLI. I've tried to set up our 802.1x/RADIUS on a 1910-8 switch in an outbuilding, and it almost works. On a windows 7 client I connect cable, enter...
View ArticleSlow ProCurve 1800-24G switch
In my home office I have recently fitted a PROCURVE J9028B 1800-24G switch. Ports 23T & 24T are LACP bonded to a Synology DiskStation. Both PC's on the network are reporting 1GB network, the...
View ArticleHP 1820 and Vlan
I have a problem to make Vlans on this switch.i have the following Vlans: vlans 1 : standardvlan10 : for networking with PCsvlan 20: for camerasvlan 30: a NAS or server 1) I put the port from the...
View ArticleHP 1910-8G and jumbo frames configuration
Hi there, I have an HP 1910-8G (JG348A) switch and am trying to view/configure jumbo frames configuration. I can't find any info on this feature in the manual, the web interface, or the CLI. I read...
View ArticleHP Switch V1910-24G-POE (170W) JE008A
I am trying to upgrade the IOS on the HP Switch with Cisco commands, I cannot seem to download the IOS from the HP site I keep getting, "The page you requested can not be found or displayed at this...
View ArticleHP v1910 24G POE Switch - Script to Auto Reboot at Specific Time
Hi!Could someone please post something to Auto Reboot HP v1910 24G POE Switch. I've created a .bat file, and I'm able to login into the Switch but don't know how to proceed further? How to put reboot...
View ArticleHP 1920-48G firmware update fail
Hello, I'm currently struggling with a HP 1920-48G-PoE switch, thr problem is as following: I tried to update the firmware (to JG928A_5.20.R1107), using the web interface. Upload went fine, and the...
View ArticleVLAN Setup on ProCurve 1810G-24
Hello, I am amateur to the networking setup and maybe this i want to achieve to be very simple. So excuse my ignorance. I have a router under a block IP of 8 static IPs. I want the one of the 8 IPs...
View ArticleConfiguring RSTP on the 1820 procurve switch
I have 5 - 1820-48port procurve switches that have all been enabled with vlan tagging/trunking and I can ping from Switch 5 to Switch 1 and back and forth and between users. Now the problem is whenever...
View Article1810 v2 qos DSCP
I posted this in another HP forum and I was told I should probably post herehttp://h30434.www3.hp.com/t5/Other-HP-Consumer-Products-and-Technologies/1810-v2-qos-DSCP/m-p/5146431/highlight/false#M20484...
View ArticleI need a Switch that can Specify up to multiple MAC addresses on 1 single...
Hi Guys I am in need of a Switch that can Specify up to multiple MAC addresses on 1 port. Reason beign is that I want to have 1 network point wich I can connect a switch on it and canoonect my...
View ArticleHP V1810 48G (J9660A) Vlan , and VLAN Trunk
Please find below how i am trying to create the vlans and trunk, but i am unable to work it out in HPV1810 Switch can anyone guide.. i have tried to find youtube videos and also blog in how to...
View ArticleGrab ARP Table via SNMP on HP v1910 Switch?
Hello, Just as the topic says, is it possible to grab the ARP table from an HP v1910 switch via SNMP? I'm currently writing a python script that will provide the user IP address to port mappings. Any...
View ArticleHP 1910 Gigabit Ethernet Switch Series Slow ports
Hi everyone, I encounter a problem with a HP v1910 48 ports (not a POE model). While there is no QOS configuration in any port, some (2 or 3) of them behave as if they were under bandwidth control....
View Article