Hello,
How can I perform a trunk between switches ports?
Thank you
Matteo
↧
Trunk switch 1820 serie
↧
HPE 1920S how to disable the admin default user
Hi, hope somebody can help me. I've added two new user with read/write-rights and for security reasons, now I want to disable the default admin user. But I can't find any way to do this, neither in the manuals nor in the web. Does anybody knows, how it goes ? Thanks, Ulrich
↧
↧
How To Disable Radio 2.4 GHZ HPE OC20
Hello , Everyone
I would like to know how to turn off the HPE OC 20 WIFI 2.4 GHZ wave because my phone is connected to 2.4 GHZ.
↧
HPE 1820 VLAN help
Good day, I ask you to help me figure out the organization of vlan in the office network. What do we have:
The Cisco RV320 Router on which to create the subnets:
- MGMT 10.100.5.0/24 VLAN 5 - DHCP OFF - ports Untagged / Inter VLAN Routing - enable
- LAN 10.100.10.0/24 VLAN 10 - DHCP ON (10.100.10.20 - 254) - Tagged / Inter VLAN Routing port - enable
- VoIP 10.100.20.0/24 VLAN 20 - DHCP ON (10.100.20.10 - 254) - Tagged / Inter VLAN Routing port - enable
- WiFi 10.100.30.0/24 VLAN 30 - DHCP ON (10.100.30.10 - 254) - Tagged / Inter VLAN Routing port - disable
With one cable, I connected port number 1 on the router to port number 48 on the switch
HPE 1820 48G Switch:
Edited the trunk (TRK1) as follows:
Trunk Name: Cisco
Admin mode: enabled
STP Mode: Disabled
Static Mode: Enabled
Load Balance: Source / Destination MAC. VLAN Ethertype incoming port
In members add the port that is connected to the router, the status has changed to Up
In VMware ESX Server (the server is connected to the switch on port 47 and 46):
Created a group of ports with VLAN20
Assigned a group to a virtual machine with a telephony server
I start the server and can not get the IP address from DHCP
I can't figure out how to configure vlan, could you help me? I know English very poorly and use a translator, sorry
↧
Connecting four 1920 switches
Hello!
I'm going to setup four HP 1920 switches, and i just need to connect them with a uplink cable, so they perform as single network.
Basically, 40 Client PCs, one Server and one Gateway and they all see each other. No need for nothing more (basically like dumb switchs).
This can be done, right?
If so, can someone help, and tell the best way to do it?
Thanks for the time.
↧
↧
Connecting four HPE 1920 switches
Hello!
I'm going to setup four HPE 1920 switches, and i just need to connect them with a uplink cable, so they perform as single network.
Basically, 40 Client PCs, one Server and one Gateway and they all see each other. No need for nothing more (basically like dumb switchs).
This can be done, right?
If so, can someone help, and tell the best way to do it?
Thanks for the time.
↧
MIB for 1820 Series
We have a lot of HPE1820 starting from 8 port to 24 both nonPoE and PoE variants across the network and are trying to set up monitoring of them all using SNMP but I cannot find where to download MIB files on the site. 1800 are added alongside their firmware but not for these. Any ideas?
↧
Issue with simple VLAN on 1910-8-PoE+ JG537A switch
Hi All,
I do not have very much knowledge about Vlans, but I thought, this simple one, with only one switch can't be a big issue… well it could…
I want to connect security cameras and Wifi APs to my HPE1910-8-PoE JG537A switch.
I created two Vlans:
Nr 10 for the cameras and 20 for the AP's.
I configured port 1/0/1 and port 1/0/6 for VLAN 10, Untagged, Access, PVID 10.
All other ports are still on the default: VLAN 1, Untagged, Access PVID 1.
The camera-server is in Port 1/0/6. For, to me, unknown reason it added “Tagged membership 1, Link Type Hybrid” automatically to the camera-server's port.
Now I cannot connect to the camera in port 1/0/1, but I can connect to the others.
Can anybody explain what I’m doing wrong here?
Thanks in advance!
Kind Regards, Johan
↧
IRF TRAFFIC VERY SLOW
HI all I have 6 switches connected to irf & two uplink.
Network performance through this stack is very poor.
Regards,
Salim
↧
↧
3COM 3CDSG8/hp v1900 8g
The switch being used lost the image on a power outage. I have changed the boot area and it appears all areas have lost the image. I can connect via console but cant seem to get the switch to accept the image I believe to be correct oc801_00_05A.bin
I am looking for detailed instructions on how to do this. I realize this is legacy equipment, but the environment I'm in, it is unfortunately necessary. Thanks in advance.
↧
JE009A ABA vs ABB
Hi, what's the difference between the JE009A switch's ABA and ABB 'tag'?
I've found a similar question on a non-HP forum for another switch, the best guess there was for supported languages, which didn't explain the price difference.
Also, is there a way to find out this ABA/ABB param for a switch (on the web gui or in cli)?
I've found a similar question on a non-HP forum for another switch, the best guess there was for supported languages, which didn't explain the price difference.
Also, is there a way to find out this ABA/ABB param for a switch (on the web gui or in cli)?
↧
HP1950 broken web interface
I have a stack of 4 HP1950s, two JG962A and two JG963A working together in an IRF stack. All of a sudden the management interface is broken. I can login but after that the menu remains empty only an error window opens with "The data error". (see here)
Looking at all the web requests I see a request to "/wnm/get.j?sessionid=abc" which gets answers with
"rpc-error":
{"/rpc-reply":and then everythings ends.
I'm quite stuck with this since these things are completely useless without a web interface since CLI is abcent. The only thing I tried so far is cycling the power. Network switching is performing without any issues. From what I can tell these all seem to run firmware version r3115p03.
I'm in the blind here. I'm looking for insights on how to analyze this and what steps to take to get this back to life.
Any insight/advice is apreciated
↧
advanced ACLs example 1920S
Someone can give an example of an ACL that denies IP traffic between two VLANs VLAN 110 and VLAN 130. I have tried to do it using advanced ACL and it has been impossible.
Please help
↧
↧
problems with intervlans communication
hi and sorry for my bad english,
i have some problems of configuration on my new installation.
i have 2 switch (2530 and 1920s) behind a stormshield appliance.
on the old installation we haven't vlan yet, and the old ip configuration is reused in the new configuration for the vlan 1.
i have 3 vlan (1 data, 20 management, 90 visitor), and here is my 1920s configuration :
!Current Configuration:
!
!System Description "HPE OfficeConnect Switch 1920S 48G 4SFP PPoE+ (370W) JL386A, PD.02.06, Linux 3.6.5-a07f8920, U-Boot 2012.10-00118-g3773021 (Oct 11 2016 - 15:39:54)"
!System Software Version "PD.02.06"
!System Up Time "0 days 23 hrs 21 mins 8 secs"
!Additional Packages HPE QOS,HPE IPv6 Management,HPE Routing
!Current SNTP Synchronized Time: SNTP Client Mode Is Disabled
!
network protocol none
network parms 192.168.20.253 255.255.255.0 0.0.0.0
vlan database
vlan 20,90,100
vlan name 20 "MANAGEMENT"
vlan name 90 "INVITE"
vlan name 100 "VOIP"
vlan routing 1 1
vlan routing 20 2
vlan routing 90 3
exitnetwork mgmt_vlan 20
ip ssh server enable
ip ssh protocol 2
sshcon timeout 30
configure
sntp server "37.187.5.167"
!clock timezone 1 minutes 0
clock timezone id 38
time-range Schedule-1
exit
time-range Schedule-2
exit
ip routing
ip helper enable
ip helper-address 192.168.1.11 dhcp
username "admin" password xxxxxxxxxxxxxxxxxxxxx level 15 encrypted override-complexity-check
no username guest
voice vlan
line console
exitline telnet
exitline ssh
exitport-channel name TRK 1 pont-HP-1920-N1
interface 46
addport TRK 1
exit
port-channel name TRK 2 ROC1
interface 47
addport TRK 2
exit
snmp-server sysname "HP-1920S-N1"
snmp-server location "N1"
snmp-server contact "administrateur"
!
ip access-list DATA
permit ip any any
exitip access-list INVITE
permit ip any any
exitip access-list MGMT
permit ip any any
exitip access-group DATA vlan 1 in 1
ip access-group MGMT vlan 20 in 1
ip access-group INVITE vlan 90 in 1interface 1
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 2
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 3
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 4
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 5
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 6
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 7
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 8
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 9
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 10
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 11
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 12
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 13
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 14
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 15
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 16
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 17
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 18
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 19
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 20
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 21
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 22
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 23
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 24
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 25
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 26
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 27
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 28
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 29
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 30
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 31
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 32
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 33
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 34
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 35
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 36
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 37
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 38
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 39
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 40
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 41
vlan pvid 100
vlan participation exclude 1,20
vlan participation include 100
exit
interface 42
vlan pvid 100
vlan participation exclude 1,20
vlan participation include 100
exit
interface 43
vlan pvid 100
vlan participation exclude 1,20
vlan participation include 100
exit
interface 44
vlan participation exclude 20
vlan participation include 100
vlan tagging 100
exit
interface 45
vlan pvid 90
vlan participation exclude 1
vlan participation include 90
exit
interface 48
vlan pvid 20
vlan participation exclude 1
vlan participation include 20
exit
interface TRK 1
vlan participation include 20,90,100
vlan tagging 1,20,90,100
exit
interface TRK 2
vlan participation include 20,90,100
vlan tagging 1,20,90,100
exit
interface vlan 1
bandwidth 10000
routing
ip address 192.168.1.253 255.255.255.0
ip mtu 1500
no ip unreachables
no ip redirects
exit
interface vlan 20
bandwidth 10000
routing
ip mtu 1500
no ip unreachables
no ip redirects
exit
interface vlan 90
bandwidth 10000
routing
ip address 192.168.90.253 255.255.255.0
ip helper-address 192.168.1.11 dhcp
ip mtu 1500
no ip unreachables
no ip redirects
exit
ip route 0.0.0.0 0.0.0.0 192.168.1.254 10exit
the ping between vlan1 and 90 work fine but vlan90 won't going out on the web.
does anyone have some ideas of what i have done wrong?
thanks in advance.
↧
HP 1950 JG961A IP-HELPER
i have a HP 1950 JG961A and i wish to add a DHCP helper to a vlan. i can't find an option in the GUI and i can find even less in "xtd-cli-mode".
Infact in xtd, i can display settings but i can't seem to conf t or en .... (i'm no wizard)
Please advise how i can complete this task.
↧
oc20 config via console port
Hi, i need to turn off the 2.4ghz radio signal in my oc20, i have connected via the console port, but have no options to turn off the 2.4ghz, does anyone know if this is possible or how to do it?
↧
HP 445010-001 | 4 / 16Q Fibre Channel Switch | AG308A
Hi
Is it possible to get hold of the firmware for this switch?
Thanks
↧
↧
HP 1950 JG961A - ACL to vLAN
I have a HP 1950 JG961A and I have created an ACL (v4) in the GUI but I can't see how you append this ACL to a vLAN ??
Please advise.
↧
Odd STP related problem in V1910 with a stacked switch
I have a very straightforward network to deal with, a central switch made up of two stacked Edgecore ecs4510-28F switches feeding 11 V1910-48G switches.
The feeds are dynamic, LACP controlled, LAGs of 4*1G fibre SFPs
At the V1910 end the LAGs are made up of ports 49-52.
At the Edgecore end the LAGs are made up of two ports each from each stack half, e g port1+2 in switch1 + port1+2 in switch2.
The topology is a simple and straightforward star, the 4*1G LAGs connect each V1910 directly to the 4510 stack, and there are no other links between switches. The V1910 rj45 ports connect to individual flats, and the risk of a loop to appear between two flats seems minute, even with Apple style ethernet bridges and wifi leakage.
Now to the problem:
If I enable STP on the MSTP global configuration page in more than one V1910, all but one V1910 will eventually be cut off from the 4510stack.
All I do is enable globally, and all else is default.
What could possibly cause this?
There are no superfluous links, and the topology will never change, but I'm still uneasy about turning STP off, which would, I suppose, solve the problem.
What would be your first thought in a situation like mine?
The feeds are dynamic, LACP controlled, LAGs of 4*1G fibre SFPs
At the V1910 end the LAGs are made up of ports 49-52.
At the Edgecore end the LAGs are made up of two ports each from each stack half, e g port1+2 in switch1 + port1+2 in switch2.
The topology is a simple and straightforward star, the 4*1G LAGs connect each V1910 directly to the 4510 stack, and there are no other links between switches. The V1910 rj45 ports connect to individual flats, and the risk of a loop to appear between two flats seems minute, even with Apple style ethernet bridges and wifi leakage.
Now to the problem:
If I enable STP on the MSTP global configuration page in more than one V1910, all but one V1910 will eventually be cut off from the 4510stack.
All I do is enable globally, and all else is default.
What could possibly cause this?
There are no superfluous links, and the topology will never change, but I'm still uneasy about turning STP off, which would, I suppose, solve the problem.
What would be your first thought in a situation like mine?
↧
HPE OfficeConnect Switch 1920S JL384A ARP Proxy
Hello, I am new to HP (networking too) and trying setup 1920S switch so pardon me if I ask what I supposed to know.
We own ancient Siemens PLCs with no option of setting gateway. The network setup consists of Kerio Control and one 1920S. I need to access the PLC from VPN client connected to Kerio Control.
I believe that 1920s is supposed to be able to use ARP proxy. But what I read about 1920s seems to be able to ARP proxy only in betwen subnets set directly on the unit. Is that right or is there a chance to make my configuration work?
I must access IP 10.10.10.1 from IP 192.168.124.10. Thanks much for sending me the right direction.
Configuration:
- Kerio Control VPN Client 192.168.124.10
- Kerio Control VPN server 192.168.124.1
- Kerio Control LAN VLAN10 10.10.10.224
- unit 1920s
routing->configuration->global routing enabled
routing for VLAN10 enabled and set IP 10.10.10.10, ARP proxy enabled
default fateway set to 10.10.10.224
PLC 10.10.10.1 (no gateway)
↧