Hi,

I have an hpe 1920s poe switch.

My ISP has given me a public IP. ... say- 202.56.230.52  sub : 255.255.255.252 , g/w -202.56.230.51

I want to create two separate vlan ..... say vlan 5 & vlan 6

vlan 5 will assign for lan connection 

vlan 6 will be assign for wi-fi connection. 

So I want to create two separate private ip pool. 192.168.1.0 network 

So tell me how is it possilble . would I have to a trunk port or jus IP route .

Tel me

P.S. :Mod: Moved as a new topic from following post

Hi Guys,

I am experiencing high latency intermittently in our internal LAN: Please help to resolve:::::

I have configured two 5940 switches in stack. 4*40Gbps ports are used for irf. Stacking is working fine. Three  "HPE OEM ProLiant BL460c Gen9"blade server are integrated with these switch. Six BAGG interfaces are created to integrate the server. Each BAGG interface contains two 40Gbps port(One from switch1 & another from Switch2). All gateways are defined in this switch. When I pinging Server IP from switch getting high latency intermittently for some server IP. If I shut switch-1' port(used in BAGG) getting latency for all server IP. But when shutting switch-2' port(used in BAGG) no latency for all IP.

Means when packet is coming via second switch, getting latency.

I checked by interchanging the cable but still latency is there. Same issue is observed for all six BAGG interface.

IP 10.60.205.1/24 is configured in this switch on interface vlan600. ping response for 10.60.205.16 ::

56 bytes from 10.60.205.16: icmp_seq=16 ttl=64 time=1.516 ms
56 bytes from 10.60.205.16: icmp_seq=17 ttl=64 time=1.464 ms
56 bytes from 10.60.205.16: icmp_seq=18 ttl=64 time=72.630 ms
56 bytes from 10.60.205.16: icmp_seq=19 ttl=64 time=19.773 ms
56 bytes from 10.60.205.16: icmp_seq=20 ttl=64 time=62.238 ms
56 bytes from 10.60.205.16: icmp_seq=21 ttl=64 time=2.343 ms
56 bytes from 10.60.205.16: icmp_seq=22 ttl=64 time=1.600 ms
56 bytes from 10.60.205.16: icmp_seq=23 ttl=64 time=2.292 ms
56 bytes from 10.60.205.16: icmp_seq=24 ttl=64 time=1.522 ms
56 bytes from 10.60.205.16: icmp_seq=25 ttl=64 time=20.496 ms
56 bytes from 10.60.205.16: icmp_seq=26 ttl=64 time=44.124 ms
56 bytes from 10.60.205.16: icmp_seq=27 ttl=64 time=2.002 ms

No latency from 10.60.205.13

56 bytes from 10.60.205.13: icmp_seq=0 ttl=64 time=1.468 ms
56 bytes from 10.60.205.15: icmp_seq=1 ttl=64 time=1.359 ms
56 bytes from 10.60.205.13: icmp_seq=2 ttl=64 time=1.493 ms
56 bytes from 10.60.205.13: icmp_seq=3 ttl=64 time=1.185 ms
56 bytes from 10.60.205.13: icmp_seq=4 ttl=64 time=1.156 ms
56 bytes from 10.60.205.13: icmp_seq=5 ttl=64 time=1.166 ms
56 bytes from 10.60.205.13: icmp_seq=6 ttl=64 time=1.266 ms
56 bytes from 10.60.205.13: icmp_seq=7 ttl=64 time=1.309 ms
56 bytes from 10.60.205.13: icmp_seq=8 ttl=64 time=1.226 ms
56 bytes from 10.60.205.13: icmp_seq=9 ttl=64 time=1.096 ms

<TOR01>display version

HPE Comware Software, Version 7.1.070, Release 2612P02

Copyright (c) 2010-2018 Hewlett Packard Enterprise Development LP

HPE FF 5940 32QSFP+ Switch uptime is 0 weeks, 0 days, 5 hours, 49 minutes

BAG Config::

========

interface Bridge-Aggregation24

description To_Enc_2_VC1_Q1_Q2_External

port link-type trunk

undo port trunk permit vlan 1

port trunk permit vlan 600 to 699

link-aggregation mode dynamic

TEST CASE::

In BAGG 24 port 1/0/19 & 2/0/19 is there. If shut 1/0/9 then latency for all IP. If shut 2/0/9 no latency for all IP. If plug out the cable from 2/0/9 and connect to 1/0/9 no latency is there.

Switch reboot and upgradation is also done but no luck.

Hi, 

I have got a network of 9(1950) switches connected in a ring topology. I want the core switch (48 Port 1950 Switch) to do intervlan routing.  I have made vlan interfaces on core swtiches for all vlan and set a static route to the firewall with a priority of 1, but it is not working can some please confirm can 1950 provide intervlan routing ? 

I have also set all the edge switches with a static route pointng to the core management vlan interface.

I use dhcp-server and the output is configured to permanent IP based on  mac-addresses.
dhcp snooping is configured on HPE. one port is trusted and all others are untrusted. This option 82 is turned off completely.
I write down the traffic coming from HPE back to dhcp server with capture tool (Mikrotik) to a file only from this port and with the condition 'port 68'
and see the following picture:
dhcp request as if you are duplicated. I see two packets in a row.
one with the original mac, the second with the HPE mac.

The switch-uplink in this case gives information messages about the need to take action.
Firmware fully updated to Version Release 1120 (2018). DHCP option 82 is not used. DHCP relay is not used.
Behavior on a larger scale is noticeable on the switch HPE 1920 48 ports, 24 ports , etc.

what's happening?
how to configure dhcp snooping simply?

must HPE duplicate DHCP replies ? 

I have some text config but it very simple :

===============display version===============
===================================================
HPE Comware Platform Software
Comware Software, Version 5.20.99, Release 1120
Copyright (c) 2010-2018 Hewlett Packard Enterprise Development LP
HPE 1920-8G Switch uptime is 0 week, 0 day, 2 hours, 43 minutes

HPE 1920-8G Switch
128M bytes DRAM
32M bytes Flash Memory
Config Register points to Flash

Hardware Version is Ver.A
Bootrom Version is 122
[SubSlot 0] 8GE+2SFP Hardware Version is Ver.A

==========================================================
===============display device verbose===============
==========================================================
Slot 1
SubSNo PortNum PCBVer FPGAVer CPLDVer BootRomVer AddrLM Type State
0 10 Ver.A NULL 000 122 IVL SMBS10 Normal
Slot 1 info:
Status : Normal
Type : SMBS10
Software Ver : Release 1120
PCB Ver : Ver.A
FPGA Ver : NULL
BootRom Ver : 122
CPLD Ver : 000
PortNum : 10
Chip : 0
Learning Mode: IVL
=================================================================
===============display current-configuration===============
=================================================================
#
version 5.20.99, Release 1120
#
sysname HP 1920G Switch
#
clock timezone Moscow add 03:00:00
#
domain default enable system
#
ipv6
#
telnet server enable
#
web idle-timeout 30
#
password-recovery enable
#
vlan 1
#
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
#
user-group system
group-attribute allow-guest
#
local-user admin
password cipher $c$3$2XXXXXXXXXXXXXXXXXXXXXXXXXX
authorization-attribute level 3
service-type telnet terminal
service-type web
#
stp mode rstp
stp enable
#
interface NULL0
#
interface Vlan-interface1
ip address 192.168.24.4 255.255.252.0
#
interface GigabitEthernet1/0/1
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/2
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/3
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/4
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/5
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/6
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/7
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/8
loopback-detection enable
port auto-power-down
stp edged-port enable
undo lldp enable
dhcp-snooping trust
#
interface GigabitEthernet1/0/9
loopback-detection enable
stp edged-port enable
#
interface GigabitEthernet1/0/10
loopback-detection enable
stp edged-port enable
#
dhcp-snooping
#
ip route-static 0.0.0.0 0.0.0.0 Vlan-interface1 192.168.24.1
#
info-center loghost 192.168.4.104
undo info-center logfile enable
#
ntp-service source-interface Vlan-interface1
ntp-service unicast-server 192.168.4.4
#
ssh server enable
#
load xml-configuration
#
user-interface aux 0
authentication-mode scheme
user-interface vty 0 15
authentication-mode scheme
#
return
===============================================================
===============display saved-configuration===============
===============================================================
#
version 5.20.99, Release 1120
#
sysname HP 1920G Switch
#
clock timezone Moscow add 03:00:00
#
domain default enable system
#
ipv6
#
telnet server enable
#
web idle-timeout 30
#
password-recovery enable
#
vlan 1
#
domain system
access-limit disable
state active
idle-cut disable
self-service-url disable
#
user-group system
group-attribute allow-guest
#
local-user admin
password cipher $c$3$XXXXXXXXXXx
authorization-attribute level 3
service-type telnet terminal
service-type web
#
stp mode rstp
stp enable
#
interface NULL0
#
interface Vlan-interface1
ip address 192.168.24.4 255.255.252.0
#
interface GigabitEthernet1/0/1
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/2
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/3
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/4
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/5
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/6
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/7
loopback-detection enable
port auto-power-down
stp edged-port enable
#
interface GigabitEthernet1/0/8
loopback-detection enable
port auto-power-down
stp edged-port enable
undo lldp enable
dhcp-snooping trust
#
interface GigabitEthernet1/0/9
loopback-detection enable
stp edged-port enable
#
interface GigabitEthernet1/0/10
loopback-detection enable
stp edged-port enable
#
dhcp-snooping
#
ip route-static 0.0.0.0 0.0.0.0 Vlan-interface1 192.168.24.1
#
info-center loghost 192.168.4.104
undo info-center logfile enable
#
ntp-service source-interface Vlan-interface1
ntp-service unicast-server 192.168.4.4
#
ssh server enable
#
load xml-configuration
#
user-interface aux 0
authentication-mode scheme
user-interface vty 0 15
authentication-mode scheme
#
return
=====================================================

Hi,

I've updated the firmware of JH295A, now when I try to log in I'm seeing the following message and I can't log in:

Login in failed, please check your network, or the HTTPS service is enable

I'm not sure what's wrong and sometimes I can connect to 443 and sometimes I can't, thanks!

Hey there, i am designing an IPTV network that can stream 4k video from the server. I am going to use HPE Officeconnect 1920s switch as an multicast switch on the network to generate and send IGMP queries to other IGMP snooping enabled switch. My question is can 1920s switch do igmp querier? Thanks.

Morning all - I work for a company that has a few sites up and down the country. We share network resources with our sister companies from within the same group.

At one of our sites one of our sister company has installed their own router linked into their MPLS cloud. I now need to separate their traffic from ours and point it to their routers.

The site uses the HPE 1920G switches which are web based - I have in mind just to VLAN off their traffic. 

There is already a global static route that points to our router, will this prevent their VLAN traffic accessing their routers? Do I need to add anymore static entires?

Many thanks.

Hi,

I am trying to configure VLAN Concept at HP 1920-24G switch.

I am setting up Windows Based Radius Server(NPS) in my platform, i have 3 switches & a AP between my firewall(testing phase) interlinked to each other.

I configured VLAN option at HP Switch using GUI mode, from firewall to HP Switch-1 i connected a uplink cable at port no 1 which is changed to Trunk Mode, from HP Switch-1 interlinked a cable from Port 2 to HP Switch-2 at Port No 1(both the Port 2 & Port 1) are changed to Trunk Mode, again from HP Switch-2 at Port No 2 connected one more uplink cable to HP Switch-3 at Port No 1(both Port 2 & Port 1) are changed to Trunk Mode.

Finally at HP Switch-3 connected one patch cable at port 23 for my Access point which too changed to Trunk Mode(that didn't worked so changed once to Tagged mode, neither works).

Can anyone please suggest me the right configuration of vlan configuration, as when client tries to connect the WiFi SSID it gets connected but IP not getting assigned based on VLAN ID.

Any help please!!!!

I have an HP 1950 switch with no added VLANs or other configuration other than setting the IP and adding a password.  The switch is at 10.0.1.106/ subnet 255.255.254.0.  From any system on that same subnet, I can ping the switch and also log into the management GUI.  We monitor our network with PRTG, it runs on a server on the server network 10.0.10.x, a firewall is segmenting the servers from the client network.  The firewall is allowing ping as well as SNMP to the switch & I can see the traffic passing through the firewall.  However, the connections fail.  I have multiple 1820 switches being monitored some on the 10.0.0.0/23 network and at 18 other locations via an MPLS circuit.  We have one other 1950 switch on the server network 10.0.10.x, it monitors correctly.  So there is something I'm missing on the problem switch.

Hi,

I got a Hp V1910-16G switch and have updated it firmware to version 5.20_R1519P03.

Am trying to setup VLAN on it as listed below, however after setting the interface IP addresses, the gateway IP of VLAN10, 20  and 1 cannot be PING.  Only on VLAN1 it can see the three gateway IPs.

For example I connect a laptop with IP 192.168.200.11 (gw 192.168.200.253).  It does not work too when I set IP of laptop to 192.168.150.12 (gateway 192.168.150.253)  I was following a vmfocus how tos titled "how to configure layer3 static routes & vlans on hp v1910 24G"  I can't seem to find out what's wrong maybe you can help.

I was assuming after setting the interface IP, routing between VLANs will work naturally.  But in actual the gateways IP are not ping able for VLAN20 & 10

VLAN1 - 192.168.100.253 for pc users

VLAN10 - 192.168.200.253 for IPCameras/CCTV

VLAN20 - 192.168.150.253 test VLAN

I've set up an HPE 1920-24G-PoE switch (JG926A) to authenticate against a Windows NPS server.  Authentication is working fine, but authenticated users do not have manager permissions.  I've set up a vendor-specific attribute as follows:

Vendor Code: 25506
Vedendor-assigned attribute number: 29
Attribute format: Decimal
Attribute value: 3

Essentially the same NPS policy (aside from this vendor-specific attribute) works perfectly on my Procurve 26XX switches with aaa authentication login privilege-mode set.

Any ideas what's going on?

Switche 1920S 48G - JL382A

May i know how to set port to limit bandwith? i can't find "line rate" under QOS section.

I am trying to find out if the HP 1920S switches are gvrp or mvrp capable.

The switch can do Radius dynamic VLAN assignment and creates the dynamic VLAN even if missing, but it does not have an uplink. This requires disconnected the device and statically creating the VLAN, which would be alleviated if gvrp/mvrp was available.

If a VLAN is created dynamically by Radius you cannot define an uplink (Tagged/Trunked) port for the VLAN as it says it was dynamically created and you cannot define settings for it.

This also means I have to statically create it at the uplink switch as the switch has gvrp on and doesn't know that the switch below is participating in the VLAN because gvrp/mvrp isn't on to let it know.

Essentially, every time I need to configure a VLAN statically on a 1920S, I have to do it statically at the above switch, as well. Adding an unneccessary amount of time for each VLAN.

I have purchased two HP 1820G switches  and wants to do simple LAN  between two areas.  networking is not establishing while connecting between switches. can any one suggest to resolve this issue, since I am new to configuration 

Hello,

on my HP1920S I would like to configure following:

- VLAN 10 - Enterprise WLAN

- VLAN 20 - WIFi Guest

I would like to know how ro do it and if is possible that switxh deines IP adrresses of clients

on VLAN's?

Thanks!

Bonjour,

Je cherche à faire du port mirroring (via interface web) sur un HP series 1950 (modéle JG962A).

Je configure mon port source et destination, j'enregistre avec succès. Le problème étant qu'apréès l'enregistrement, le port source reste le GE1/0/1 et la direction en "incoming".

Le statut du port mirroring est "incomplete".

Résultat, impossible de faire une configuration comme je l'entends.

Quelqu'un aurait-il une idée pour solutionner mon probléme ?

Merci.

Google Translated

Hello, I am looking to port mirroring (via web interface) on a HP series 1950 (model JG962A).

I configure my source and destination port, I register successfully. The problem is that after the recording, the source port remains the GE1 / 0/1 and the direction in "incoming".

The status of the mirroring port is "incomplete".

Result, impossible to make a configuration as I hear.

Would anyone have an idea to solve my problem?

Thank you.

I'm trying to upgrade the firmware on my HP 1920 switch.  I was on release 1114 and noticed that the latest firmware required bootrom 122 or newer.  So I checked all the old versions and version 116 was the latest firmware that requires 117 or newer.  The switch BootRom was 119, and from previous experience, the Boorom is updated with the firmware automatically.  So I upgraded to firmware 1116 but it is still showing 119 for the bootrom. 

How can I upgrade to the bootrom 122 so I can upgrade the firmware on the switch to 1121?

Hi..Everybody...

I am going to enabling dot1x authentication process in comware version switches.and some of the ports has been connected to Printers.dot1x will not work on Printers ports.so for printer ports what security need to enable.please suggest any one solution for this query.i am struck in the process...

El problema se presenta en un momento a otro, se deconecta y no muestra su ip. Intentas acceder a su ip que vino de fábrica, error de bota, no se puede actualizar el firmware o todo caso restablecer un modo de fábrica,  Alguna modo de solucionar ese problema?